Occasional ContributorHello,
Can I program this kit's FPGA using a .sof file or do I need to first generate a .flash file? Please include instructions if a .sof file is sufficient. Thanks.
Super ContributorAll FPGAs can be programmed with a .sof file via the JTAG interface, either JTAG directly or usually using JTAG to USB conversion (USB Blaster). You just use the standalone Programmer or the Programmer included with a full installation of Quartus.
Occasional ContributorThanks.
I'm using the Arria 10 GX FPGA Development Kit (DK-DEV-10AX115S-A) and trying to configure its FPGA (10AX115S2F45I1SG) with a .sof file and a USB Blaster cable. I get this:
Error (209015): Can't configure device. Expected JTAG ID code 0x02E660DD for device 1, but found JTAG ID code 0x020A30DD. Make sure the location of the target device on the circuit board matches the device's location in the device chain in the Chain Description File (.cdf).
The FPGA listed on the device search of Quartus Prime Standard 23.1 gives the 10AX115S2F45I2SGES as being installed on the kit board:
Which device part number should I be using, 10AX115S2F45I1SG or 10AX115S2F45I2SGES? What is the cause of the error? Thanks.
Super ContributorDid you auto select the device in the Programmer or manually select it? Try manually selecting the device.
And show a screenshot of what the Programmer is showing you.
Occasional ContributorI've selected both devices (different compilations) and selected the devices manually in the Programmer. Programming fails with either compiled .sof file.
Here's the programmer and error message with 10AX115S2F45I2SG selected:
Error (209015): Can't configure device. Expected JTAG ID code 0x02E660DD for device 1, but found JTAG ID code 0x020A30DD. Make sure the location of the target device on the circuit board matches the device's location in the device chain in the Chain Description File (.cdf).
Here's the programmer and error message with 10AX115S2F45I1SG selected:
Error (209015): Can't configure device. Expected JTAG ID code 0x02E660DD for device 1, but found JTAG ID code 0x020A30DD. Make sure the location of the target device on the circuit board matches the device's location in the device chain in the Chain Description File (.cdf).
Any ideas? Thanks.
Super ContributorHi,
The part number should be 10AX115S2F45I1SG.
https://www.intel.com/content/www/us/en/products/details/fpga/development-kits/arria/10-gx.html
Regards,
Aiman
Occasional ContributorHi,
Occasional ContributorThe error description I'm getting is this:
Error (209015): Can't configure device. Expected JTAG ID code 0x02E660DD for device 1, but found JTAG ID code 0x020A30DD. Make sure the location of the target device on the circuit board matches the device's location in the device chain in the Chain Description File (.cdf).
Code 0x020A30DD is for a 5M1270Z MAX V device. This is not the device I selected for the file (10AX115S2F45I1SG) and doesn't appear to be anywhere on the Arria 10 GX FPGA Development Kit I'm using. How is the programmer finding this?
Super ContributorHi,
Since you are using dev kit, there is a switch to disable the MAX V on the dev kit. Please disable the switch and try to configure again.
Please also try the JTAG chain debugger after disable MAX V.
Regards,
Aiman
Occasional ContributorHi,
I've put development board switch SW4-2 in the ON position to disable the MAX V in the JTAG chain as described in the kit user guide:
However, the programmer still fails to configure the Arria 10:
Error (209015): Can't configure device. Expected JTAG ID code 0x02E660DD for device 1, but found JTAG ID code 0x020A30DD. Make sure the location of the target device on the circuit board matches the device's location in the device chain in the Chain Description File (.cdf).
And the MAX V still shows up in the JTAG chain:
Any ideas? Thanks.
Occasional ContributorHi Aiman,
Here are the board's SW3-SW6 switch positions. SW4-2 is in the ON position yet the MAX V device is still in the JTAG chain. Can you provide any further assistance? Thanks.
Super ContributorJust for shiggles, how about flipping SW4-1 and SW4-2 to their opposite positions and see if there's a change in the JTAG chain?
Super ContributorHi,
May I know where you are from? We can set up a call to look at this case.
Me and my team are based in Malaysia.
Regards,
Aiman
Super ContributorHi,
I have sent the meeting invite.
Regards,
Aiman
Occasional ContributorHi Aiman,
Thanks. I'll be on the call.
Super ContributorHi,
Thanks for taking the call.
Per our conversation through the call:
-You will provide board serial number
-You will provide the top marking
-I will check your access for the IPS.
Regards,
Aiman
Occasional ContributorHi Aiman,
Thanks for the call. Here is the board:
How soon could I get a replacement board? Any progress with restoring the IPS access?
Thanks.
Super ContributorHi,
I am checking for the board warranty for now.
For IPS access, sorry to let you know that your company is no longer eligible for IPS access. You are always welcome to get support from FPGA Forum or to reach out to your support FAE.
Regards,
Aiman
Super ContributorHi Chris,
(DK-DEV-10AX115S-A) is still in warranty. I am in the process of applying for RMA.
Will update you soon.
Regards,
Aiman
