Low Latency 100G Ethernet Intel FPGA IP Hardware Design Example

Hi i have another question. I made a wrapper with 2 instances of the IP. It gets synthetized and implemented correctly but it doesn't pass the timing analysis (there is an epic slack, like -90). I don't understand why, i'm looking the paths and it seems like it's something related to the pll that generates the clk100. Have you got any advice please?

Hi,

i temporarely stopped working on transceivers. Now i'm back on it and i'm trying to figure out the pinout. I downloaded the 1SM21C document by Intel.

I don't understand the relation between the pins and the transceivers. For example, the board i'm using is a BittWare 520N-MX with an Intel Stratix-10 FPGA connected to four QSFP28 ports.

I need to use two of those QSFP28 ports. In particular i need to use the Ethernet 100Gb Hard IP which seems to be usable via port 2 and 3 on the board. So i'm looking forward to the pinout of the port 2 and 3.

The board document says that:

QSFP0_RX[0]p -> pin BB45

QSFP0_RX[0]n -> pin BB44

QSFP0_TX[0]p -> pin BD49

QSFP0_TX[0]n -> pin BD48

and then it says that the rest of the pin mappings follow numerically.

Then i took a look at the Intel document 1SM21C.

I'm a bit confused because in the verilog code RX and TX wires are buses [3:0] so each of them is made of 4 wires.

I don't understand what pin corresponds to each of those wires and also how do i differentiate each QSFP(n) from each other.

For example, i want to use QSFP2 and QSFP3 and i know that each rx and tx wires are composed of 4 wires each. How should i look at the Intel document?

Sorry i'm new to it ...

Since there are no recent activities, I’ll set this case to close-pending. If you’re still in need of assistance, please reopen this case within the next 20 days.

Yes, if using more than one Jtag master, there will have multiple IDs, and you need to select the right one for each instance. To assign the base address, one of the methods is to use avmm master bridge from platform designer (One Jtag Master connect to two AVMM master bridge).

Regards -SK

I've noticed this part on the ethernet_link_inspector guide:

3. In the Ethernet Link Inspector - Link Monitor tab, follow these steps to set the

correct JTAG to Avalon Master path:

a. Load the Programming File (*.sof) in System Console by clicking File ➤

Load Design for the detailed JTAG to Avalon Master path.

b. Select List JTAG Masters to see all available JTAG to Avalon Master paths.

c. Select a JTAG to Avalon Master path number from the drop-down box and click

Set JTAG Master.

Note: Each JTAG to Avalon Master path lists two TYPE_NAME (marked by the

blue box in the figure below). The instance name of the JTAG to Avalon

Master path is displayed in one of these TYPE_NAME along with the text

FULL_HPATH (marked by the orange box in the figure below). Select the

JTAG to Avalon Master path number that has the instance name of the

JTAG to Avalon Master path connected to the Ethernet IP.

Seems like they are using multiple jtag masters and then choosing the connected to the IP of interest.

Can the addressing be managed by the system console somehow?

Do i need to create a demux to route the data to the right IP or there is any tool in quartus that makes it?

Yes, it looks fine.

Regards -SK

Thank you, i get it now. Can you at last confirm if this architecture is correct?

You can use ONE Jtag Master connects to two Ethernet IP with a difference base addresses.