Introducing the Altera Community AI Responder — Beta
Altera is introducing the AI Responder, an assistant built into the Altera Community to help provide faster, context-aware guidance for Altera product questions. It uses relevant public Altera documentation and Knowledge Database content, with coverage continuing to expand. The AI Responder may provide source references and can hand off complex or out-of-scope questions to an Altera subject-matter expert. As a beta feature, responses may contain errors or omissions, so please review the sources and verify technical guidance against official Altera documentation before implementation. If the response does not fully address your question, add more context and tag ai_responder to continue the discussion. We welcome your feedback as we improve the Community experience.
Agilex 5E HPS and Linux
Hi. 1. Is there a simple method to run two Linux systems on HPS, i.e.: Linux 1 - 2xA55 and Linux 2 - 2xA76 with different sets of peripherals? 2. Is it possible to use one Ethernet port by these two Linux systems. 3. Is there a simple method for communication between these two Linux systems?
SoC EDS, compile uboot for Arria 10 SoC
Hi, I have a product with Arria 10 SoC, 10AS066H3F34I2SG. I need to compile uboot. I have a Linux Ubuntu 24.04.2 machine (x86 64-bit). I previously used SoC EDS 19.1 on an older Linux machine. I downloaded the Linux version for this and installed it. As other discussions here have asked installing EDS appears to require dependencies such as libc6:i386 libncurses5:i386 libstdc++6:i386 zlib1g:i386 Just installing EDS does not complete the DS-5 install (the ARM 32-bit libraries appear to be missing). I assume the 32-bit ARM libraries are required to compile uboot. Am I making correct assumptions on the required dependencies to compile uboot? The i386 dependencies appear to no longer have valid fingerprint keys for Ubuntu 24. How can I compile uboot? Best regards, Pete
Arria 10 SoC – USB devices always enumerating as Full-Speed (Yocto 4.1, dwc2)
Hello, My name is Ángel and I am currently working with an Intel SoC FPGA Arria 10. I am trying to connect an Intel RealSense SR300 camera to my system, but I am experiencing USB speed negotiation issues. Environment: Platform: Intel SoC FPGA Arria 10 OS: Linux (custom image built with Yocto 4.1 Langdale) USB driver: dwc2 librealsense built with -DFORCE_RSUSB_BACKEND=ON When I connect the RealSense SR300 camera, the USB link does not negotiate correctly and the device is always enumerated as Full-Speed (12M) instead of High-Speed or SuperSpeed. At first, I suspected a problem with the USB 3.0 connector of the SR300. However, when I tested with a standard USB 2.0 webcam, I observed exactly the same behavior: the device is still enumerated only as Full-Speed (12M). This suggests the issue is likely related to the USB controller configuration on the Arria 10 rather than the camera itself. System Output lsusb -t: /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M |__ Port 1: Dev 2, If 0, Class=Vendor Specific Class, Driver=, 12M |__ Port 1: Dev 2, If 1, Class=Audio, Driver=, 12M |__ Port 1: Dev 2, If 2, Class=Audio, Driver=, 12M dmesg: [ 204.765768] usb 1-1: new full-speed USB device number 2 using dwc2 Yocto local.conf: MACHINE = "arria10" DISTRO_FEATURES:append = " systemd vfat" DISTRO_FEATURES:remove = " sysvinit" VIRTUAL-RUNTIME_init_manager = "systemd" IMAGE_INSTALL:append = " kernel-module-uvcvideo" KERNEL_MODULE_AUTOLOAD += "uvcvideo" IMAGE_INSTALL:append = " \ packagegroup-core-boot \ pciutils \ usbutils \ v4l-utils \ i2c-tools \ librealsense2 \ " EXTRA_OECMAKE:append:pn-librealsense2 = " -DFORCE_RSUSB_BACKEND=ON" Any guidance would be greatly appreciated.
Cyclone5 SoC: U-Boot not detecting USB-HUB
Hello there, I'm working on a design on top of a Chameleon96 Board (CycloneV based), featuring a USB OTG Chip USB3300, and connected to it an USB 2513B Hub. My issue is that neither U-Boot or Linux are able to detect the USB Hub connected to the USB3300. This used to work with older U-Boot versions and are still working on my board, but I was not able to reproduce such behavior with up-to-date versions (cloned from https://github.com/altera-fpga/u-boot-socfpga and https://github.com/altera-fpga/linux-socfpga). The Chameleon96 has two GPIO pins to control the reset of the mentioned USB chips, with a fixed configuration on the USB 2513B (the I2C interface is not exposed). With my version (U-Boot 2025.07-gd4f268660a70-dirty and Linux 6.12.33-g3234b1ed8956), the USB OTG is detected and the hub registered with logs like the following: [ 0.883275] dwc2 ffb40000.usb: supply vusb_d not found, using dummy regulator [ 0.890619] dwc2 ffb40000.usb: supply vusb_a not found, using dummy regulator [ 0.898034] dwc2 ffb40000.usb: Configuration mismatch. dr_mode forced to host [ 0.905721] dwc2 ffb40000.usb: DWC OTG Controller [ 0.910454] dwc2 ffb40000.usb: new USB bus registered, assigned bus number 1 [ 0.917571] dwc2 ffb40000.usb: irq 32, io mem 0xffb40000 [ 0.923324] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, b2 [ 0.931588] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber1 [ 0.938800] usb usb1: Product: DWC OTG Controller [ 0.943509] usb usb1: Manufacturer: Linux 6.12.33-g3234b1ed8956 dwc2_hsotg [ 0.950362] usb usb1: SerialNumber: ffb40000.usb [ 0.955682] hub 1-0:1.0: USB hub found [ 0.959499] hub 1-0:1.0: 1 port detected but the connected USB hub never shows up. Similarly 'usb start' from the U-Boot prompt just shows something called U-Boot Root Hub: => usb start starting USB... USB DWC2 Bus usb@ffb40000: 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found => usb tree USB device tree: 1 Hub (480 Mb/s, 0mA) U-Boot Root Hub Older u-boot versions (and linux) are able to detect the USB hub after 'usb start'. In this case, the root hub is named DWT OTC RootHub, and I don't know if this is just a change of naming somewhere or something wrong is also happening while detecting the USB3300 Hub: SOCFPGA_CHAMELEON96 # usb start (Re)start USB... USB0: Core Release: 2.93a scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found SOCFPGA_CHAMELEON96 # usb tree USB device tree: 1 Hub (480 Mb/s, 0mA) | DWC OTG RootHub | +-2 Hub (480 Mb/s, 2mA) the linux kernel (4.1.33-ltsi-altera) is also able to detect the USB Hub as can be seen in these logs: [ 0.913203] ffb40000.usb supply vusb_d not found, using dummy regulator [ 0.919864] ffb40000.usb supply vusb_a not found, using dummy regulator [ 0.957196] dwc2 ffb40000.usb: EPs: 16, dedicated fifos, 8064 entries in SPRM [ 1.817295] dwc2 ffb40000.usb: DWC OTG Controller [ 1.822011] dwc2 ffb40000.usb: new USB bus registered, assigned bus number 1 [ 1.829076] dwc2 ffb40000.usb: irq 44, io mem 0x00000000 [ 1.834617] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.841394] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber1 [ 1.848596] usb usb1: Product: DWC OTG Controller [ 1.853282] usb usb1: Manufacturer: Linux 4.1.33-ltsi-altera-svn260 dwc2_hsog [ 1.860481] usb usb1: SerialNumber: ffb40000.usb [ 1.865670] hub 1-0:1.0: USB hub found [ 1.869457] hub 1-0:1.0: 1 port detected ... [ 2.367190] usb 1-1: new high-speed USB device number 2 using dwc2 [ 2.577385] usb 1-1: New USB device found, idVendor=0424, idProduct=2513 [ 2.584069] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.591939] hub 1-1:1.0: USB hub found [ 2.595782] hub 1-1:1.0: 3 ports detected I think I've ported all the needed configuration to the u-boot sources (basically resetting the USB hub using the attached GPIOs, and I also tried the reset sequence manually from U-Boot with the gpio command) and I'm not able to figure out how to find where the issue might be. I've forked u-boot sources here: https://github.com/teiram/u-boot-socfpga/, using the socfpga_chameleon96_defconfig configuration. Could you please support me in order to troubleshoot what the issue might be? I tried to backport my changes to some different branches on u-boot-socpfga but got the same results or even worse (no boot at all). I also have sources for a working U-Boot but they are quite old and the configuration changed sensibly since. I think all the needed options are set. Cheers, ManuelValidating ECC Functionality on Custom Agilex 5 SOM in Linux Kernel
We are now looking to validate ECC (Error Correction Code) functionality on our custom Agilex 5 System-on-Module (SOM) running Linux. Our objective is to ensure that ECC is correctly enabled and functioning across all relevant memory regions, and that error detection and correction mechanisms are properly integrated at the kernel level. Could you please provide guidance on the necessary kernel configurations, device tree modifications, and available tools or procedures to test and monitor ECC behavior on this platform? Any documentation or reference designs specific to Agilex 5 ECC support would be highly valuable.
Main Features Released in 25.1.1
Main Features Released in 25.1.1: Initial support of the Agilex 3 device. Released GSRD for the Agilex 3 C-Series Development Kit. Reference: https://altera-fpga.github.io/rel-25.1.1/embedded-designs/agilex-3/c-series/gsrd/ug-gsrd-agx3/ DDR ECC support in the Agilex 5. Support of production Agilex 7 F-Series Crypto device. GSRD for DK-DEV-AGF0123FA dev kit (using production AGFD023R24C2E1VC ) replaces the DK-DEV-AGF027F1ES dev kit (using engineering sample AGFB027R24C2E2VR2). Reference: https://altera-fpga.github.io/rel-25.1.1/embedded-designs/agilex-7/f-series/fpga/gsrd/ug-gsrd-agx7f-fpga/ Support of USB 3.1 in Agilex 5 GSRDs. Support of booting from eMMC in ATF to Linux Direct boot for Agilex 5 device. Reference: https://altera-fpga.github.io/rel-25.1.1/embedded-designs/agilex-5/e-series/premium/boot-examples/ug-linux-boot-agx5e-premium/#boot-from-emmc_1 Removed generation of NAND binaries in Agilex 5 GSRD. Will be re-enabled when production devices get released.
Sopc2DTS with Agilex 7
After generating a qsys_top.sopcinfo with quartus for the SocFPGA Agilex 7 design, i'm trying to get the .dts then the .dtb from it via sopc2dts. I'm encountring the following issue: $ java -jar sopc2dts.jar --input ../Bureau/qsys_top.sopcinfo --output essai_libs.dts --type dts --extra-component-libs sopc_components_altera.xml --extra-component-libs sopc_components_fps.xml --extra-component-libs sopc_components_labx.xml --extra-component-libs sopc_components_others.xml Unsupported interface kind: ftile_hssi_system_clock_source Unsupported interface kind: ftile_hssi_reference_clock_source Unsupported interface kind: ftile_hssi_reference_clock_sink Unsupported interface kind: ftile_hssi_reference_clock_sink Unsupported interface kind: ftile_hssi_reference_clock_sink Unsupported interface kind: ftile_hssi_reference_clock_sink Unsupported interface kind: ftile_hssi_reference_clock_sink Unsupported interface kind: ftile_hssi_reference_clock_sink Unsupported interface kind: ftile_hssi_reference_clock_sink Unsupported interface kind: ftile_hssi_reference_clock_sink Unsupported interface kind: ftile_hssi_system_clock_sink ... Unsupported interface kind: ftile_hssi_system_clock_source Unsupported interface kind: ftile_hssi_reference_clock_source Component agilex_hps of class intel_agilex_hps is unknown Component emif_cal_0 of class altera_emif_cal is unknown Component emif_cal_1 of class altera_emif_cal is unknown Component emif_fpga of class altera_emif_fm is unknown Component emif_fpga_1 of class altera_emif_fm is unknown Component emif_hps of class altera_emif_fm_hps is unknown Component mm_ccb_0 of class mm_ccb is unknown Component mm_ccb_1 of class mm_ccb is unknown Component qsys_top_mux_ddr0 of class mux_ddr0 is unknown Component qsys_top_mux_ddr1 of class mux_ddr0 is unknown Component user_rst_clkgate_0 of class altera_s10_user_rst_clkgate is unknown Component agilex_hps of class intel_agilex_hps is unknown Component emif_cal_0 of class altera_emif_cal is unknown Component emif_cal_1 of class altera_emif_cal is unknown Component emif_fpga of class altera_emif_fm is unknown Component emif_fpga_1 of class altera_emif_fm is unknown Component emif_hps of class altera_emif_fm_hps is unknown Component mm_ccb_0 of class mm_ccb is unknown Component mm_ccb_1 of class mm_ccb is unknown Component qsys_top_mux_ddr0 of class mux_ddr0 is unknown Component qsys_top_mux_ddr1 of class mux_ddr0 is unknown Component user_rst_clkgate_0 of class altera_s10_user_rst_clkgate is unknown Component agilex_hps of class intel_agilex_hps is unknown Component emif_cal_0 of class altera_emif_cal is unknown Component emif_cal_1 of class altera_emif_cal is unknown Component emif_fpga of class altera_emif_fm is unknown Component emif_fpga_1 of class altera_emif_fm is unknown Component emif_hps of class altera_emif_fm_hps is unknown Component mm_ccb_0 of class mm_ccb is unknown Component mm_ccb_1 of class mm_ccb is unknown Component qsys_top_mux_ddr0 of class mux_ddr0 is unknown Component qsys_top_mux_ddr1 of class mux_ddr0 is unknown Component user_rst_clkgate_0 of class altera_s10_user_rst_clkgate is unknown Component xcvr_12a_bank_systemclk_f_0 of class systemclk_f is unknown Component xcvr_12a_bank_xcvr_12a_fmc_quad2 of class directphy_f is unknown Component xcvr_12a_bank_xcvr_12a_fmc_quad3 of class directphy_f is unknown Component xcvr_12a_bank_xcvr_12a_qsfp of class directphy_f is unknown Component xcvr_13a_qsys_fmc of class directphy_f is unknown Component xcvr_13a_qsys_qsfp1 of class directphy_f is unknown Component xcvr_13a_qsys_systemclk_f_0 of class systemclk_f is unknown Component xcvr_13c_qsys_fmc of class directphy_f is unknown Component xcvr_13c_qsys_systemclk_f_0 of class systemclk_f is unknown Unable to find a master of type CPU. Randomly selecting the first master we find (agilex_hps). How to fix this and have a complete and correct device tree that can be compiled into .dtb? I'm working with agilex 7. + if i wanna custom an OS and do it in the HPS of my board (like adding new modules using gpios), is it mandatory to add some blocks in the .dts ?"DMA engine initialization failed" error when EMAC uses GMII interface
I am seeing the error given here when I boot the Agilex A5 (Quartus 24.3). This doc recommends to connect mac_tx_clk_i to a 2.5/25 MHz clock source 'correctly'. What does it mean, 'correctly'? There is a field in the HPS docs for this signal here, but this also does not specify what 'correctly' means. For further reference, I am trying to connect EMAC0 to EMAC1. Also here is the .dts: &gmac0 { status = "okay"; mac-mode = "gmii"; phy-mode = "gmii"; fixed-link { speed = <1000>; full-duplex; }; }; &gmac1 { status = "okay"; mac-mode = "gmii"; phy-mode = "gmii"; fixed-link { speed = <1000>; full-duplex; }; }; Many thanks! K