Epcs64

Hi Aley,

You were right! There is a SST25VF064C assembled on my board. Not the one I had expected from the schematic.

But after copying your file to "C:\altera\15.0\nios2eds\bin\" I still get the same error as befor. Could it be that I did some wrong configuration in the quartus?

I did make the internal RAM bigger, thats why the addresses are now different.

Info: 16.10.2015 15:21:31 - (FEIN) sof2flash: Starting

Info: Info: *******************************************************************

Info: Info: Running Quartus II 64-Bit Convert_programming_file

Info: Info: Command: quartus_cpf --no_banner --convert --device=EPCS128 --option=C:/proj/46C_leer_nios_at50MHz_ok/46C_leer/flash/46C_leer_epcs.opt C:/proj/46C_leer_nios_at50MHz_ok/46C_leer/output_files/46C_leer.sof C:/proj/46C_leer_nios_at50MHz_ok/46C_leer/flash/46C_leer_epcs.pof

Info: Info (210033): Memory Map File C:/proj/46C_leer_nios_at50MHz_ok/46C_leer/flash/46C_leer_epcs.map contains memory usage information for file C:/proj/46C_leer_nios_at50MHz_ok/46C_leer/flash/46C_leer_epcs.pof

Info: Info: Quartus II 64-Bit Convert_programming_file was successful. 0 errors, 0 warnings

Info: Info: Peak virtual memory: 250 megabytes

Info: Info: Processing ended: Fri Oct 16 15:21:36 2015

Info: Info: Elapsed time: 00:00:03

Info: Info: Total CPU time (on all processors): 00:00:03

Info: Info: *******************************************************************

Info: Info: Running Quartus II 64-Bit Convert_programming_file

Info: Info: Command: quartus_cpf --no_banner --convert C:/proj/46C_leer_nios_at50MHz_ok/46C_leer/flash/46C_leer_epcs.pof C:/proj/46C_leer_nios_at50MHz_ok/46C_leer/flash/46C_leer_epcs.rpd

Info: Info: Quartus II 64-Bit Convert_programming_file was successful. 0 errors, 0 warnings

Info: Info: Peak virtual memory: 248 megabytes

Info: Info: Processing ended: Fri Oct 16 15:21:42 2015

Info: Info: Elapsed time: 00:00:04

Info: Info: Total CPU time (on all processors): 00:00:04

Info: 16.10.2015 15:21:43 - (FEIN) sof2flash: Done

Info: Using cable "USB-Blaster [USB-0]", device 1, instance 0x00

Info: Resetting and pausing target processor: OK

Info: Reading System ID at address 0x00012048: verified

Info: Processor data bus width is 32 bits

Info: Looking for EPCS registers at address 0x00011800 (with 32bit alignment)

Info: Initial values: 0001703A 04C00074 9801483A 9CFFF804 983FFD1E 0000203A

Info: Not here: reserved fields are non-zero

Info: Looking for EPCS registers at address 0x00011900 (with 32bit alignment)

Info: Initial values: 93000237 6300080C 603FFD26 90000335 A8000C26 03010004

Info: Not here: reserved fields are non-zero

Info: Looking for EPCS registers at address 0x00011A00 (with 32bit alignment)

Info: Initial values: 02C02004 002EE03A 00000F06 90000335 4000683A 0017883A

Info: Not here: reserved fields are non-zero

Info: Looking for EPCS registers at address 0x00011B00 (with 32bit alignment)

Info: Initial values: 3180080C 300C96BA 701CD07A 719CB03A 843FFFC4 803FF81E

Info: Not here: reserved fields are non-zero

Info: Looking for EPCS registers at address 0x00011C00 (with 32bit alignment)

Info: Initial values: 00000000 00000000 00000260 00000000 00000000 00000001

Info: Valid registers found

Info: EPCS signature is 0xBF

Info: EPCS identifier is 0xBF254B

Info: No EPCS layout data - looking for section [EPCS-BF254B]

Info: Unable to use EPCS device

Info: Leaving target processor paused

Error: Error code: 8 for command: nios2-flash-programmer "C:/proj/46C_leer_nios_at50MHz_ok/46C_leer/flash/46C_leer_epcs.flash" --base=0x11800 --epcs --sidp=0x12048 --id=0x12345678 --timestamp=1445000242 --device=1 --instance=0 '--cable=USB-Blaster on localhost [USB-0]' --program --verbose