User Profile

amildm

Contributor

Joined 4 years ago

172 Posts4 Solutions

View All Badges

User Widgets

Contributions

Re: [ISSP] In-System Source and Probe -> How to insert to RTL?
The Solution was chosen, thanks for your support! You can close the thread
2 years ago Place Quartus® Prime
1.6KViews
0likes
0Comments
Re: [HDMI IP] Auxiliary Packet Encoder -> Data Width -> could be changed?
What do you mean "re-wrap it to another format"? Could you please provide an example?
2 years ago Place IP & Transceiver
1.3KViews
0likes
0Comments
Re: [HDMI IP] Vendor Specific Infoframes -> how to insert?
Hi ZH_Intel, Thanks a lot for your response. As for the HDMI RX (Sink), is it able to receive multiple VSI infoframes within the same Video frame (my previous question was about sending the multiple VSI) ? Thanks!
2 years ago Place IP & Transceiver
2.3KViews
0likes
0Comments
Re: Avalon ST Multiplexer -> is it possible to concatenate?
The proposed solution is under test, will update the thread with the results
2 years ago Place IP & Transceiver
1.7KViews
0likes
0Comments
[ISSP] In-System Source and Probe -> How to insert to RTL?
Hello, I'm using Quartus v19.3. How is it possible to insert the ISSP to RTL? How to define several ISSP's - each one synchronous to its driving clock?? Should I add synchronous stages to ISSP? How? Should ISSP be based on the Signal Tap signals? Cannot I define different signals for ISSP and SignalTap? Thanks!
Solved
2 years ago Place Quartus® Prime
Platform
1.8KViews
0likes
3Comments
Re: [HDMI IP] Vendor Specific Infoframes -> how to insert?
Does the Core support the 3D meta data extention (VSI extended frame - see below)?
2 years ago Place IP & Transceiver
2.4KViews
0likes
0Comments
[HDMI IP] Auxiliary Packet Encoder -> Data Width -> could be changed?
Hi All, Is it possible to change a width of the aux_data width in the HDMI IP? By default it's defined to be 72bit. This input port belongs to the Auxiliary Packet Encoder Data of the HDMI IP. Thanks!
Solved
2 years ago Place IP & Transceiver
Video
1.4KViews
0likes
4Comments
Re: Avalon ST Multiplexer -> is it possible to concatenate?
The Avalon-ST Multiplexer doesn't have the Packet User Signal, only Start of Packet and End Of Packet. Again, as for the picture below, how will the inputs in0 through in19 be scheduled on the OUT output? The in0 .. in19 are packet based 16bits width inputs (with start-of-frame and end-of-frame signals). How should I configure the MUX0 and MUX1 so that on the OUT port will be observed packets in0, in1, ... in19 in this certain order (in0, in1, ..., in19)? Thanks!
2 years ago Place IP & Transceiver
1.8KViews
0likes
2Comments
Re: [HDMI IP] Vendor Specific Infoframes -> how to insert?
Is there any response/solution? The issue is pretty urgent for us...
2 years ago Place IP & Transceiver
2.4KViews
0likes
0Comments
Re: Avalon ST Multiplexer -> is it possible to concatenate?
Let's say I concatenate them in the following way: So, how will the inputs in0 through in19 be scheduled on the OUT output? The in0 .. in19 are packet based 16bits width inputs (with start-of-frame and end-of-frame signals). How should I configure the MUX0 and MUX1 so that on the OUT port will be observed packets in0, in1, ... in19 in this certain order (in0, in1, ..., in19)? Thanks!
2 years ago Place IP & Transceiver
1.9KViews
0likes
0Comments