Forum Discussion

Rk_Athram's avatar
Rk_Athram
Icon for Occasional Contributor rankOccasional Contributor
3 years ago

Remote system update for arria10 FPGA

Hi,

we are using Arria 10 FPGA DEVICE "10AX057N2F40E2SG", we needed to use Remote system update feature for our custom board.


From the intel design store, there are two reference design modules.

But from rocketboards website it is stated as

https://www.rocketboards.org/foswiki/Documentation/RemoteSystemUpdateCompatibility

"The Remote System Update (RSU) is a feature available for Stratix 10 and Agilex FPGA devices"

please Clarify whether Arria10 will support or NO!

Thanks,

Rajesh

Configuration

29 Replies

Show More
  • tehjingy_Altera's avatar
    tehjingy_Altera
    Icon for Regular Contributor rankRegular Contributor
    3 years ago

    Hi Rajesh


    Before you start the steps of flashing the application image did you flash the ru.jic image to setup the flash layout?


    Regards

    Jingyang, Teh


  • Rk_Athram's avatar
    Rk_Athram
    Icon for Occasional Contributor rankOccasional Contributor
    3 years ago

    Hi Jingyang, Teh

    Yes, we are maintaining factory image, by programming ru.jic.

    Regards,

    Rajesh

  • tehjingy_Altera's avatar
    tehjingy_Altera
    Icon for Regular Contributor rankRegular Contributor
    3 years ago

    Hi Rajesh


    Did you flash the initial image to set up the image layout for the Factory and the Application Image?


    Regards

    Jingyang, Teh


  • Rk_Athram's avatar
    Rk_Athram
    Icon for Occasional Contributor rankOccasional Contributor
    3 years ago

    Hi Jingyang, Teh

    Yes

    Is example design working for you!

    Regards,

    Rajesh

  • tehjingy_Altera's avatar
    tehjingy_Altera
    Icon for Regular Contributor rankRegular Contributor
    3 years ago

    Hi Rajeesh

    Sorry for the late reply.

    I just tried out the example design and found that the files in the example design is not working.

    I will work with the owner on this.

    Mean while you could try out the files attached.

    I have created it base on the user guide of the example.

    Please refer to the .map for the start and end address.

    Regards

    jingyang, Teh

  • Rk_Athram's avatar
    Rk_Athram
    Icon for Occasional Contributor rankOccasional Contributor
    3 years ago

    Hi Jingyang, Teh

    I think you missed files attachment/ link.

    Regards,

    Rajesh

  • tehjingy_Altera's avatar
    tehjingy_Altera
    Icon for Regular Contributor rankRegular Contributor
    3 years ago

    Hi Rajesh


    The files are up now in the case comment previously.

    Could you try check it out again?


    Regards

    Jingyang, Teh


  • tehjingy_Altera's avatar
    tehjingy_Altera
    Icon for Regular Contributor rankRegular Contributor
    3 years ago

    Hi Rajesh


    Any update on this case?

    Did you manage to try out the files that I have shared?


    Regards

    Jingyang, Teh


    • Rk_Athram's avatar
      Rk_Athram
      Icon for Occasional Contributor rankOccasional Contributor
      3 years ago
      Hi Jingyang, Teh



      Still the attachment is missing.



      Regards,

      Rajesh
  • tehjingy_Altera's avatar
    tehjingy_Altera
    Icon for Regular Contributor rankRegular Contributor
    3 years ago

    Hi Rajesh

    So sorry that you could not see the attached file.

    Let me reattach it here.

    It is a zip file case.zip and the content of the zip are as follows:

    Regards

    Jingyang, Teh

    • Rk_Athram's avatar
      Rk_Athram
      Icon for Occasional Contributor rankOccasional Contributor
      3 years ago

      Hi Jingyang, Teh

      Thanks for your time and efforts.

      Can you please share the project as well, to create new application file with our requirement needs the changes in design from the example design .

      otherwise changing to new application image wont take effect and it may go to factory image.



      Regards,

      Rajesh