User Profile
TRAN_HIEU_007
Occasional ContributorJoined 5 years ago
User Widgets
Contributions
Re: Cyclone 10GX with 2 port SFP 1G test.
XCVR and TSE ping tests ran in Cyclone 10GX KIT but not ran in my custom board. Can you tell me why and how to fix the above problem to work properly XCVR? VCCT_GXB = VCCR_GXB = 1.03V; VCCH_GXB = 1.8V and all signal TX and RX same in both my wide KIT and custom DEV.4.5KViews0likes0CommentsRe: Cyclone 10GX with 2 port SFP 1G test.
Hi. SengKok_L_Intel. I have been test successful Ping from Bercut to Cyclone 10GX kit use TSE ipcore over SFP 1G module. But when I test in my custom broad have error (Can't setup Ethernet link synchronization). My broad similar DEV 10GX kit. All signal ok such as ref_clk = 125m; SFP_TX_DIS_0 =0; SFP_FALT_0 = 0 but no signal in SFP_RX0_P and SFP_RX0_N. So I think XCVR_Native in my Broad error. I try test XCVR using "Cyclone 10 GX XCVR Toolkit Reference Design v17.1.1 User Guide" on tranceiver toolkit has eror below.4.6KViews0likes0CommentsRe: New port Ethernet use Cyclone10GX KIT error.
Hi Eng Wei. Currently I still fail with this project. I have tried many solutions including test loopback on Module FMC_Loopback using Transceiver toolkit and have been successful. But when transmitting through the SFP port, there is an error. Can you point out what is the correct I/O configuration for the TXP and RXP pins? I don't know if you have tried the 1G baseX transmission test project using the Cyclone10Gx chip yet? Thank you very much!1.5KViews0likes0CommentsRe: Cyclone 10GX with 2 port SFP 1G test.
I can't sucess this test. I'm not sure that the Cyclone 10gx supports 1G SFP communication or I have misconfigured IPCore TSE. Can you help me try the above example on a Cyclone10gx kit. If that fails I fear that having to switch to using Xilinx IC:4.7KViews0likes0CommentsRe: Cyclone 10GX with 2 port SFP 1G test.
Hi SengKok. I have been tried "AN744: Scalable Triple Speed Ethernet Reference Designs for Arria 10 Devices" but projet not ran in TEST_1588 0 1 1G test in above. In project "Single-Port Triple-Speed Ethernet and On-Board PHY Chip Reference Design - Arria 10 " TSE run in SGMII interface with 88e1111. But I need interface with SFP port.4.7KViews0likes0CommentsRe: Cyclone 10GX with 2 port SFP 1G test.
Hi SengKok! My team has build a project ping test success from Computer/Bercut <-> RJ45 caple <-> 88E1111<-> SGMIII<-> TSE IP. Can you help me change to project test to Computer/Bercut <-> SFP Caple <-> SFP 1G module<-> XCVR<-> TSE IP? Thank so much! My project test is below. https://drive.google.com/file/d/1aZt2EIvVLVoqDmtknu724jLimWsUk57V/view?usp=sharing4.8KViews0likes0CommentsRe: Cyclone 10GX with 2 port SFP 1G test.
I have tested successfully with TEST_PHYSERIAL_LOOPBACK and TEST_SMA_LB in both broad (My custom broad and C10 GX development board). Moreover, I do not understand why when I disconnect SFP cable TEST_SMA_LB still successful. This is my project test in Quartus 18.0 https://drive.google.com/file/d/1F2bbFeMCh-TXbeFQpxwCKBGHeSaQj4gC/view?usp=sharing Can you give true project test SFP 1G for Cyclone10GX. I need ping from my computer to custom broad over SFP module and TSE IP.4.8KViews0likes0Comments