mabdrahi
ContributorJoined 4 years ago
User Profile
Contributor
User Widgets
Contributions
Re: Linux not Booting on custom Intel Cyclone V board
Hi Akash, I copy the email thread from our college to here for better community understanding. ########################### EMAIL THREAD #################################### As discussed on phone, I followed the steps till "make -j 48" command. I am attaching the tree log of u-boot-socfpga folder for your reference. The qar project is updated with 4 bit sd card peripheral. Regards, Akash. From: "jeetesh kumar tiwari" <jeetesh.kumar.tiwari@intel.com> To: "Akash Gupta" <AKASH.DEAL@GOV.IN> Cc: "JS HYANKI" <js.hyanki.deal@gov.in> Sent: Friday, December 1, 2023 8:18:03 AM Subject: RE: Altera Cyclone V SoC development kit-Ready Linux Images Hi Akash, We can have call today. Last two days I was quiet busy with Intel IFTD event in Bangalore. Regards Jeetesh From: Akash Gupta <akash.deal@gov.in> Sent: Wednesday, November 29, 2023 12:43 PM To: Tiwari, Jeetesh Kumar <jeetesh.kumar.tiwari@intel.com> Cc: JS HYANKI <js.hyanki.deal@gov.in> Subject: Re: Altera Cyclone V SoC development kit-Ready Linux Images Hi, I used the same project and compiled it in Quartus Prime 18.1 and then followed this guide (which uses an old u-boot) to generate the preloader-mkpimage.bin, which I wrote as a preloader in a2 partition of sdcard. In addition, I wrote "hello-mkimage.bin" (a simple DS-5 project to display hello world over bare metal) as bootloader. Now the custom board boots up properly and log shows that SDRAM is detected. The problem is that, after reset, sometimes the output showa complete "Hello World!" phrase, but other times it shows "He" or "He▒lo World!" (including a corrupted letter) or nothing. It is totally random in nature. I am attaching both logs for your reference. We programmed the board using sof also for testing but there is no change in the nature of output. If there had been a hardware problem or RAM was not configured properly in quartus project, this preloader would not have been able to detect the RAM. Please go through the logs. You can call me at 2 PM today if you are available, otherwise convey your suitable timings. --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- About the linux booting using Quartus 22 as you and I were doing earlier, we had made few changes in the hardware and using the same project and method, now the error is changed to following: U-Boot SPL 2022.04-gfda0d917-dirty (Nov 22 2023 - 14:12:39 +0530) Trying to boot from MMC1 unable to select a mode spl: mmc init failed with error: -524 SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### Earlier, it used to show "spl: partition error", but now it show "unable to select a mode." Regards, Akash. From: "jeetesh kumar tiwari" <jeetesh.kumar.tiwari@intel.com> To: "Akash Gupta" <AKASH.DEAL@GOV.IN> Cc: "JS HYANKI" <js.hyanki.deal@gov.in> Sent: Tuesday, November 28, 2023 12:03:05 PM Subject: RE: Altera Cyclone V SoC development kit-Ready Linux Images Hi Akash, As discussed over the phone, I am getting the error while compilation. It looks DDR issue. Please send the quartus 18 version project which you have tested with baremetal. Regards Jeetesh From: Akash Gupta <akash.deal@gov.in> Sent: Tuesday, November 21, 2023 10:17 AM To: Tiwari, Jeetesh Kumar <jeetesh.kumar.tiwari@intel.com> Cc: JS HYANKI <js.hyanki.deal@gov.in> Subject: Re: Altera Cyclone V SoC development kit-Ready Linux Images Hi, Please find attached the project and error screenshot. The project was compiled using Quartus Prime 22. I have removed the "output_files" and "software" (for size purpose) folders as you will compile it again. Regards, Akash. From: "jeetesh kumar tiwari" <jeetesh.kumar.tiwari@intel.com> To: "Akash Gupta" <AKASH.DEAL@GOV.IN> Cc: "JS HYANKI" <js.hyanki.deal@gov.in> Sent: Tuesday, November 21, 2023 4:43:18 AM Subject: RE: Altera Cyclone V SoC development kit-Ready Linux Images Hi Akash, As discussed over phone, please send the quartus project so that we can also check our side. Regards Jeetesh From: Tiwari, Jeetesh Kumar Sent: Monday, November 20, 2023 12:17 PM To: Akash Gupta <akash.deal@gov.in> Cc: JS HYANKI <js.hyanki.deal@gov.in> Subject: RE: Altera Cyclone V SoC development kit-Ready Linux Images Hi Akash, We can have call today at 2:30PM. Regards Jeetesh -----Original Message----- From: Akash Gupta <akash.deal@gov.in> Sent: Monday, November 20, 2023 11:43 AM To: Tiwari, Jeetesh Kumar <jeetesh.kumar.tiwari@intel.com> Cc: JS HYANKI <js.hyanki.deal@gov.in> Subject: RE: Altera Cyclone V SoC development kit-Ready Linux Images Hi, I and Hyanki sir wanted to discuss a few things with you regarding design of custom cyclone v board. Please tell when you are available for a call. Regards, Akash. ----- Original Message ----- From: Akash Gupta <akash.deal@gov.in> To: jeetesh kumar tiwari <jeetesh.kumar.tiwari@intel.com> Cc: JS HYANKI <js.hyanki.deal@gov.in> Sent: Fri, 10 Nov 2023 17:55:29 +0530 (IST) Subject: RE: Altera Cyclone V SoC development kit-Ready Linux Images Hi, The board does not hang on the said line. It restarts automatically. The log I've attached is without any keyboard input or power button press. I am using putty on Ubuntu 18.04. Regards, Akash. ----- Original Message ----- From: jeetesh kumar tiwari <jeetesh.kumar.tiwari@intel.com> To: Akash Gupta <AKASH.DEAL@GOV.IN> Cc: JS HYANKI <js.hyanki.deal@gov.in> Sent: Fri, 10 Nov 2023 15:17:07 +0530 (IST) Subject: RE: Altera Cyclone V SoC development kit-Ready Linux Images Hi Akash, Is your board automatically restarted or stopping in between and is it hanging at “[ 1.542258] Synopsys Designware Multimedia Card Interface Driver”. My side this same image is working fine on Altera Cyclone V SoC kit. Log Attached in email. Also, Which serial terminal you are using e.g. putty or Hercules or any other utility. Regards Jeetesh From: Akash Gupta <akash.deal@gov.in> Sent: Friday, November 10, 2023 2:11 PM To: Tiwari, Jeetesh Kumar <jeetesh.kumar.tiwari@intel.com> Cc: JS HYANKI <js.hyanki.deal@gov.in> Subject: Re: Altera Cyclone V SoC development kit-Ready Linux Images Hi Jeetesh, Thanks for the image. I was able to boot linux on Altera SoCDK but it seems to stuck in a loop for me. For setting up the board pin config, I followed this link.<https://www.rocketboards.org/foswiki/Documentation/AlteraSoCDevelopmentBoardSoftwareGettingStarted> As it seems, the boot processes is stuck in a loop. I have attached the log from my putty terminal. I will try for custom board later this week, and will update you by 17.10.23. Regards, Akash Gupta. ________________________________ From: "jeetesh kumar tiwari" <jeetesh.kumar.tiwari@intel.com<mailto:jeetesh.kumar.tiwari@intel.com>> To: "Akash Gupta" <AKASH.DEAL@GOV.IN<mailto:AKASH.DEAL@GOV.IN>> Sent: Friday, November 10, 2023 10:49:46 AM Subject: Altera Cyclone V SoC development kit-Ready Linux Images Hi Akash, As discussed over phone, please download the files from the below shared details- Secureftp.intel.com - Sign In - FileTransferWebUI<https://secureftp.intel.com/secureftp> Username: tmp04946 Password: Akash@123 Host Name: secureftp.intel.com Server/Protocol Type: FTP/SSL (AUTH_SSL, AUTH_TLS, or Explicit SSL/TLS) Mode: Passive Port: 21 Let us know if you are able to download. Regards Jeetesh -- Akash Gupta, Sc-B, DEAL (DRDO) Raipur Road, Dehradun - 248001 (INDIA) +91 (135) 222 3016 | akash.deal@gov.in -- Akash Gupta, Sc-B, DEAL (DRDO) Raipur Road, Dehradun - 248001 (INDIA) +91 (135) 222 3016 | akash.deal@gov.in -- Akash Gupta, Sc-B, DEAL (DRDO) Raipur Road, Dehradun - 248001 (INDIA) +91 (135) 222 3016 | akash.deal@gov.in4.7KViews0likes0CommentsRe: Cannot Erase or Program QSPI Flash for Arria 10 Custom Board
Hi Richard, I shall set this case to close pending. If you still need further assistance, you are welcome reopen this case within 20days or open a new case, someone will be right with you. If you happened to close this case you will receive a survey. If you think you would rank your support experience less than 4 out of 5, please allow me to correct it before closing or if the problem can’t be corrected, please let me know the cause so that I may improve your future service experience. Thank you, Aliff2.2KViews0likes0CommentsRe: Cannot Erase or Program QSPI Flash for Arria 10 Custom Board
Hi Richard, Actually i have tried at my end, but i dont see the same thing as yours. It might your custom board have design issue. Can you recheck and compare Aria 10 devkit versus your design and also circuit. Thank you, Aliff2.3KViews0likes0CommentsRe: Arria 10 Linux Kernel
Hi Joshua, As we do not receive any response from you on the previous question/reply/answer that we have provided. Please login to ‘https://supporttickets.intel.com’, view details of the desire request, and post a feed/response within the next 15 days to allow me to continue to support you. After 15 days, this thread will be transitioned to community support. The community users will be able to help you on your follow-up questions. Thank you, Aliff2.3KViews0likes0Comments